ECO Refill 9.3/4"
Non-Washable Refill · Does Not Reduce Chlorine · Suspended Particle Retention in Water
100% polypropylene filter element with Melt Blown technology, indicated for point of entry. Reduces sand, mud and rust, with easy change and flow rate of 1,200 l/h.
- Max. flow rate
- 1,200 L/h
- Refill service life
- 6 months
- ≥ 15 a < 30 µm
- Classe D
- Sediment Retention
Our sales team responds within 24 business hours.
Overview
About this product
The ECO 9.3/4" Refil is the filtration element for point of entry compatible with the ECO 9.3/4" Filter and universal 9.3/4" housings, indicated for installation before the water tank or inlet manifold. Produced 100% in non-toxic polypropylene with Melt Blown technology, its raw material is heated and extruded into small filaments that form the refil's micropores, guaranteeing efficient filtration throughout the product's service life.
With its rigid structure, it prevents the formation of preferential water pathways and reduces rust particles, which stain clothes and accumulate in equipment — resulting in greater safety in daily use and longer service life for the entire hydraulic installation.
Key benefits:
- Snap-fit filtration element, with greater security and convenience when replacing
- Melt Blown technology, which prevents preferential water pathways
- Flow rate of 1,200 L/h
- Filtration grade of 25 microns (much smaller than a grain of sand, between 200 and 500 microns)
- Particle retention Class D
- Easy replacement, compatible with the ECO 9.3/4" Filter (code 907-2323) and universal 9.3/4" housings
Usage recommendation: if the element saturates quickly, installation of a pre-filter with high flow rate pleated element is recommended. After replacing the refil, it is also recommended to clean the water tank and perform a complete inspection of the seals.
Complies with Health Ministry Ordinance PRC MS nº 5/2017 and standard NBR 16098:2012.
Technical sheet
Technical specifications
Performance
- Max flow rate (L/h)
- 1,200 L/h
- Service life (months)
- 6 months
- Filtration class
- Classe D (≥ 15 a < 30 µm)
- Bacteriological filtration
- No
- Efficiency
- Sediment Retention
Operating conditions
- Water temperature
- 5 °C to 50 °C
- Working pressure
- 19.6 kPa to 588 kPa
- Installation position
- Vertical
Dimensions
- Height
- 24.8 cm
- Width
- 6,3 cm
- Depth
- 6,3 cm
- Diameter
- 2,5"
Materials and refill
- Composition
- polypropylene
- Refill composition
- Polypropylene MeltBlow
- Washable refill
- No
Standards and certificates
- Standards and certifications
- NBR 16098:2012
Installation
Step by step
Connections
- Installation position
- Vertical
- Inlet connection
- Push-fit
- Outlet connection
- Push-fit
In the box
- 1 ECO Refil 9.3/4"
- Close the water meter shutoff valve.
- Unscrew the filter bowl. If necessary, use the wrench that comes with the equipment.
- With a glove, remove the refill full of impurities and discard it. Make proper waste separation; the saturated refill is a contaminated residue.
- Clean the bowl, the o-ring and the filter cover. Use only water and biodegradable soap. Avoid abrasive materials.
- With the components clean, check the condition of each part. Make sure the o-ring (code 913-2465) is not broken or dried out, to perform its replacement.
- Position the o-ring in the housing of the internal part of the bowl.
- Insert the clean refill into the bowl and screw on the cover, ensuring proper filter sealing.
- Open the main shutoff valve and monitor the first few minutes of operation. In case of leakage, check the inlet and outlet connections and the tightness of the bowl with the cover.
ECO Refill 9.3/4"
SKU 905-0561