Wall-Mount Tap w/ POP Purifier White
Reduces chlorine, taste and odors · Activated Carbon · Water Purifier · Natural Water
Complete tap and purifier system, ready for wall installation. Reduces chlorine, dirt and water odor with triple filtration. Available in white and black.
- Max. flow rate
- 20 L/h
- Refill service life
- 1,000 L
- Chlorine reduction
- 75%
- ≥ 15 a < 30 µm
- Classe D
- Sediment Retention
- Chlorine Reduction
Our sales team responds within 24 business hours.
HF40 Short Thread Refill
Official replacement refill for this product.
Overview
About this product
The POP White Wall-Mount Tap with Purifier is a complete solution for those who want filtered water directly from the tap, with simple and practical wall installation. The system comes ready-to-use, combining tap and filter in a single product.
Its threaded activated carbon filter element reduces chlorine present in water, as well as the unpleasant smell and taste it causes in excess. Filtration occurs in three stages: first, water passes through a polypropylene barrier (Melt Blown) that retains suspended dirt; then, it passes through an internal activated carbon chamber, responsible for dechlorination; and finally, it passes through a new layer of polypropylene for final clarification, delivering cleaner water with pleasant taste.
Main benefits:
- Disposable filter element, no backwashing required
- Minimum 75% reduction of free chlorine
- Particle Retention Class D
- Flow rate of 20 l/h
- Recommended for wall installations
- Available in white (code 907-2286) and black (code 907-2363)
Usage recommendation: to ensure water quality, replacement of the filter element is recommended every 1,000 liters, 4 months or when a reduction in water flow is observed.
Complies with Ministry of Health Ordinance PRC MS No. 5/2017 and standard NBR 16098:2012.
Technical sheet
Technical specifications
Performance
- Max flow rate (L/h)
- 20 L/h
- Service life (liters)
- 1,000 L
- Service life (months)
- 6 months
- Filtration class
- Classe D (≥ 15 a < 30 µm)
- Chlorine reduction (%)
- 75 %
- Bacteriological filtration
- No
- Efficiency
- Sediment Retention · Chlorine Reduction
Operating conditions
- Water temperature
- 5 °C to 50 °C
- Working pressure
- 19.6 kPa to 392 kPa
- Installation position
- Vertical
Dimensions
- Height
- 24 cm
- Width
- 26 cm
- Depth
- 10 cm
Materials and refill
- Composition
- Polypropylene and granulated activated carbon
- Washable refill
- No
Standards and certificates
- Standards and certifications
- NBR 16098:2012 · INMETRO · ABRAFIPA
Installation
Step by step
Connections
- Installation position
- Vertical
- Inlet connection
- 3/4" threaded connection
In the box
- 1 Tap with Purifier
- 1 HF 40 Refill
- 1st Close the main shutoff. At the location where the filter will be installed: remove the tap or remove the water point cap.
- 2nd Observe all connections and flush the piping before performing the installation.
- 3rd If you don't have space to rotate the entire assembly, unscrew the tap and filter and screw only the adapter into the point of use. Use thread seal tape for the connection.
- 4th Open the main shutoff and check that all connections are properly sealed and show no leaks.
- 5th Discard the first 10 liters of water in order to remove excess carbon powder.
- 6th Your purifier is ready to use!
- Note: Routinely clean the cup and filter cap. Use only water and biodegradable soap. Avoid abrasive materials.
Maintenance
How to replace the refill
-
Step 01
Close the purifier tap. Unscrew the cap to remove the filter element that is attached to it. You can also remove the cup to clean it.
-
Step 02
Replace the filter element by screwing it onto the cup cap. Make sure the new element is properly screwed onto the cap.
-
Step 03
Check the seal of your filter before opening the tap. In case of leaks, check the tightness of the cup and cap.
-
Step 04
Attention: discard the first 10 liters of water until the water becomes clear so that the refill releases the carbon powder.
Wall-Mount Tap w/ POP Purifier White
SKU 907-2286